Stage Equipment351

Adam Hall 19" Parts 87451 Smart C

Professional rack light with patented Smart Motion Sensor Technology.Strip with 18 LEDsIndependent colour selection for active mode and sleep modeTimer control and adjustable sleep mode dimmerContinuous dimmingColour selectorOperating voltage: 12 V DCColour of lamp: blue, Cold white, green, red,

Adam Hall 87402S Rack Case

Rack Drawer 2 U Steel with 200 mm Depth. | | Made in: China | Weight: 6,9 kg

Adam Hall PCL 10

Power conditioner with rack lighting. Reliable protection against over-voltage and impulse voltage. Effective high frequency filter against interference. Central power supply with 8 switchable IEC sockets. Unswitched convenience socket on the front. Resettable circuit breaker on the front panel

ADJ ACA-SW/Pin Truss accessory

High-quality, universal cone inlay for ACA-SW/Pin Inlay for Conus Case, and its pins can hold 96 cones. The Accu-Case accessory is made of strong, 9 mm thick plywood. In a black finish. | Made in: China

ADJ ACA/WB

Heavy duty wheel board made of 20 mm MDF wood with 10 cm fully turning wheels with brakes and a cut-out for handling. Dimensions: 155 x 650 x 520 mm. Finished in black color. | Made in: China

ADJ ACA/WB

Heavy duty wheel board made of 20 mm MDF wood with 10 cm fully turning wheels with brakes and a cut-out for handling. Dimensions: 155 x 650 x 520 mm. Finished in black color. | Made in: China

ADJ Encore FR150z Theater Reflector

Part of the Encore stage lighting series, the Encore FR150Z lighting fixture is equipped with an 8-inch Fresnel lens and powered by a 130W LED engine. It produces a white wide, soft-edged beam for stage and theatre use at 3000K. It comes with barn doors to adjust the beam dispersion and a manual

ADJ Encore FR50z Theater Reflector

Part of the Encore stage lighting series, the Encore FR50Z lighting fixture is equipped with a 6-inch Fresnel lens and powered by a 50W LED engine. It produces a white wide, soft-edged beam for stage and theatre use at 3000K. It comes with barn doors to adjust the beam dispersion and a manual know

Allen & Heath ME-1 Personal Mixer

The ME-1 personal mixer is a small 40 channel mixer with a mono/stereo or headphone output. The OLED display provides information about level, selected audio source, etc. The connection is via standard Cat5e Ethernet cabling and can be distributed thru standard IT hardware. 16 buttons provide a

Allen & Heath ME-500

ME-500 is a powerful walk-up-and-mix solution that’s quick to set up and easy for just about anyone to learn in moments. The ME-500 personal mixer’s intuitive hands-on controls and crisp visual display make it easy for musicians to quickly build and control their own monitor mixes. With plug

Allen & Heath ME-U

ME-U is a touring grade, 10 port PoE hub providing power and audio to multiple ME-1 and/or ME-500 personal mixers. ME-U’s default input card allows seamless integration with Allen & Heath dLive, Avantis, SQ and Qu mixers. Fitting a Dante or MADI option card to the ME-U allows users of other pro

ART P16

Patch panel. Ideal for any live PA rack, studio rack or fixed installation where easy access to XLR inputs are required, the P16 brings all rear-mounted XLR inputs from various devices to one, convenient single space rackmountable location. The P16 saves wear and tear on the connectors of expensive

ART PB4x4

The voltage stabilizer with a capacity of 1800 W and a solid steel construction. It has RFI and EMI filters and a built-in Surge and Spike Protection system designed to protect the powered device. On the front panel there is a 15 A circuit breaker, switch and backlit input voltage meter. There are

ART PS4X4-PRO

Presenting the 4×4 PRO SERIES Power Distribution Systems from ART. Built on the foundation of the popular 4x4s, the PRO SERIES are durably constructed, reliable power conditioners for use in many applications. Wherever power management system is required, the 4×4 PRO SERIES provide the surge

ART SP4x4

Power distribution system. The SP 4x4 features a backlit linear meter to monitor input voltage, which gives the user a familiar analog style readout when monitoring voltage from a power source. Four of the eight rear outputs are 1,25 inches apart. This allows the user to plug in wide power cables

ART TPatch

The ARTcessories TPatch is a compact 8-point balanced patchbay that organizes your cables into a convenient central location on your studio desktop. Designed for maximum flexibility, the TPatch has 1/4 '' TRS phone connectors user selectable normal and half-normal modes.The compact black-anodized

Artiphon Orba Silicone Sleeve BK

Add an extra layer of protection to your Orba with Silicone Sleeve. This flexible sleeve allows full access to buttons and cable ports and features a removable strap long enough to attach Orba to your wrist or backpack. Silicone cover for Artiphon Orba Device fully playable and operable Carrying

Artiphon Orba Travel Case

Protect your Orba with our impact-resistant softshell case, made from durable EVA plastic foam, and lined with soft fabric. Beneath the zippered lid is a compartment for your charging cable, and there’s a lanyard for carrying or clipping the case to your backpack. Shockproof softshell bag for

Avante 1161350020

Whells for Avante A15S and A18S subwoofers. 4x wheels with brake | Made in: China

Behringer Eurorack Ears (70HP)

The Behringer EURORACK EARS (70 HP) is a pair of mounting brackets that allow Behringer synthesizers and other 3U format equipment to fit in all 70 HP EURORACK chassis. | | Made in: China

Behringer Eurorack Ears (80HP)

The Behringer EURORACK EARS (80 HP) is a pair of mounting brackets that allow Behringer synthesizers and other 3U format equipment to fit in all 80 HP EURORACK chassis. | | Made in: China

Behringer Eurorack Rack

The EURORACK RACK is ideal for any Behringer Eurorack-style synthesizer or equipment. This desktop/rack-mount kit converts a 19” rack into an 84 HP Eurorack chassis. A compact 4 HP power supply with two flying bus boards are included together with a 3A universal power adapter. 52 sliding nuts

Behringer GMX-300 3 m

The GMX-300 connects your microphones or stage equipment directly to any XLR audio source and is optimized for stage and studio applications.The GMX Series multicore cables are available in two different lengths for all types of setups: 10 ft/3.0 m, 16.4 ft/5.0 mThe GMX-300 features a 8 x 0.22 mm²

Behringer GMX-500 5 m

The GMX cables connects your microphones or stage equipment directly to any XLR audio source and is optimized for stage and studio applications. The GMX Series multicore cables are available in two different lengths for all types of setups: 10 ft/3.0 m, 16.4 ft/5.0 m. The GMX cables features a 8 x

Behringer P16-M

Compact 16-channel digital stereo mixer/in-ear monitor system that features an ultra-intuitive 'analogue' operation with total recall of 16 presets for custom mixes. It is equipped with state-of-the-art 24-bit D/A converters for premium audio quality and 16 Channel Select buttons with dual LEDs for

Behringer PMC-1000 Black 10 m

The GMX cables connects your microphones or stage equipment directly to any XLR audio source and is optimized for stage and studio applications. The GMX Series multicore cables are available in two different lengths for all types of setups: 10 ft/3.0 m, 16.4 ft/5.0 m. The GMX cables features a 8 x

Behringer Powerplay P1

Personal In-Ear amplifier ideal for stage and studio applications offering a reliable and affordable personal monitoring solution. This In-ear stereo system provides the option of a stereo or mono signal and is powered by a 9V battery with a 12-hour operating time. It is controlled by

Behringer Powerplay P16D Ultranet

16-channel digital ULTRANET distribution hub for expansion of Behringer’s P16-I in-ear monitoring system, providing bus-power and 16-channel signal transmission for all 8 outputs: one ULTRANET input feeds 8 ULTRANET outputs (RJ-45). Up to six P16-D ULTRANET distributors can be combined for a

Behringer Powerplay P2

Ultra-compact in-ear monitor amplifier for personal monitor applications. It features ultra-compact and lightweight design, high power and 'drummer proof' headphones output, XLR and TRS input connector with locking mechanism, level control with power on/off switch and stereo/mono source switch

Behringer Powerplay PM1

Personal in-ear monitor Belt-Pack for personal monitor applications. It offers high quality volume control, XLR input with locking mechanism, 3.5 mm mini jack headphones connector and 'Built-like-a-tank' impact-resistant metal chassis. Convenient belt-pack clip is included. | Colour: Black | UK/EU

Behringer PX 3000 ULTRAPATCH PRO

Professional multi-functional 48-point 3-mode balanced patchbay that eliminates cable clutter in the studio and adding order and clarity. It provides fully balanced high-quality 6.3mm TRS connectors and 3 modes, easily selectable per channel via top-side switches. The ''Normal'' mode interconnects

Bespeco BPRACKM8

Standard table mount 19” x 8U rack stand made of 20 x 20 mm steel, painted with nontoxic powder. It provides carrying capacity of 40 kg and nonslip, nonscratch rubber feet. | Depth (cm): 36.0 | Load Capacity: 40 kg | Type: Stand | Height (cm): 43.0 | Weight: 1,5 kg | Made in: China | Width (cm): 48.0

Bespeco CRO23EX Rack Case

Rack case from Bespeco. Made of 5 mm marine pine plywood and scratchproof laminate. 36 cm depth (34 cm effective distance between rack bar and bottom). Covers equipped with butterfly latches. Sturdy handles with spring release. Double frontal rack bar. Resistant silver anodized aluminum profiles

Bespeco CRO24EX Rack Case

Rack case from Bespeco. Made of 5 mm marine pine plywood and scratchproof laminate. 36 cm depth (34 cm effective distance between rack bar and bottom). Covers equipped with butterfly latches. Sturdy handles with spring release. Double frontal rack bar. Resistant silver anodized aluminum profiles

Bespeco CRO28EX Rack Case

Rack case from Bespeco. Made of 5 mm marine pine plywood and scratchproof laminate. 36 cm depth (34 cm effective distance between rack bar and bottom). Covers equipped with butterfly latches. Sturdy handles with spring release. Double frontal rack bar. Resistant silver anodized aluminum profiles

Bespeco PR2K

Bespeco PRK

Oneunit 19” rack level from METAL series made of 15/10 sheet iron with black nontoxic powder painted surface.  | Made in: China

Bespeco RACKB10

10U rack construction for installations in recording studios that is compatible with Bespeco RACKB10R. It is made of sturdy metal with nontoxic powder coating for better protection of the instruments.  | Made in: China

Bespeco RACKB10R

10U rack for installations in recording studios that provides maximum carrying capacity of 70 kg and useful depth of 485 mm. It is made of sturdy metal with black nontoxic powder finish. | Made in: China | Width (cm): 54.0 | Type: Rack | Depth (cm): 48.0 | Height (cm): 62.0 | Load Capacity: 70 kg | Weight: 11 kg

Bespeco RM2EX Rack Case

Made of ABS. Covers equipped with butterfly latches. Sturdy aluminium handles. Front and rear rack bar. Screws set for equipment assembling included. Black color. | | Weight: 4 kg | Made in: China

Bespeco RMTROLLY

Sliding platform for rack cases, equipped with fully rotating wheels and brakes. It is made of wood in black color, dimensions: 620 x 515 x 18 mm. | Made in: Italy

Black Lion Audio PBR8 500

Equipped with a fully balanced TT/Bantam patchbay, the PBR-8 is an 8-slot 500 Series chassis with unlimited routing options for quickly dialing in sounds without your modules having to be mounted in any particular order. With the PBR-8, you can easily audition a signal chain, re-route it, split it

Black Lion Audio PG-2 F

The PG-2 F provides clean and sufficiently dimensioned power for your equipment. In its production, high-quality components are used, including Panasonic and Wima capacitors. Thanks to their excellent properties and PG-99 technology, up to 99.7% of high-frequency noise and interfering components

Black Lion Audio PG1-F

The PG-1 Type F is built using premium Panasonic and Wima capacitors, due to their superior execution in eliminating high frequency noise that robs equipment of its peak performance. In testing, this has provided an average of 99.7% of noise filtering. Combine that superior power filtration with an

Boss CB-BU10

Specially designed for music products and accessories, the CB-BU10 provides a protective, well-organized home for your gear while traveling around town and beyond. This quality backpack-style bag is ideal for carrying a BOSS multi-effects processor or Loop Station plus cables, pedals, footswitches,

Chauvet Nimbus Cart

Nimbus Cart easily transports your Nimbus dry ice machine to and from the car and around the dance floor. Four high-strength, ball bearing casters allow for smooth transportation, while two locking casters securely transport Nimbus by locking it in place. Highlights:Easily transport your Nimbus

Cordial CYB-STAGE-BOX-CARRY-CASE 3

dB Technologies LVX XM12 Active Stage Monitor

Two-way active stage monitor from LVX series that is equipped with heavy duty components and features a particular coaxial horn design, delivering a powerful yet clear sound quality. The design enhances the benefits of coaxial wedges concept and does not only shape high frequencies’ directivity,

dbx PMC16

Personal monitor controller. The PMC16 is a 16 channel personal monitor controller which allows the user to create a custom mix from 16 channels of audio. Designed to be used with the dbx TR1616 or any other BLU link compatible device, the PMC16 allows for monitoring with headphones, in-ear

Decksaver BEHRINGER RD-9

Behringer RD-9 cover is custom-moulded to perfectly fit whilst accommodating cables, meaning the RD-9 can sit ready for operation while being fully protected. Super durable polycarbonate shell features extreme durability and offers the highest degree of protection.You will never have to worry about

Decksaver BEHRINGER X-TOUCH

While the X-Touch might be the perfect controller for your Ableton, Logic or the like, it doesn’t have the perfect protection against damage and any other bad mishaps.To fix this problem they have carefully crafted and manufactured a cover to protect the Behringer X-Touch. Super durable

Decksaver LE Behringer X-Touch One

Custom moulded in the UK to fit the contours of the LE Behringer X-Touch One. Super durable polycarbonate shell offers a high level of protection and slides straight into equipment bags, making it ideal for the travelling. Shields faders and controls from dust, liquid and accidental impact whilst

Decksaver Le Soundswitch Control One

Custom moulded in the UK to fit the contours of the Le Soundswitch Control One. Super durable polycarbonate shell offers a high level of protection and slides straight into equipment bags, making it ideal for the travelling. Shields faders and controls from dust, liquid and accidental impact whilst

Decksaver RME Babyface Pro FS & Madiface Pro

Custom moulded in the UK to fit the contours of the RME Babyface Pro FS & Madiface Pro. Super durable polycarbonate shell offers a high level of protection and slides straight into equipment bags, making it ideal for the travelling. Shields faders and controls from dust, liquid and accidental

Decksaver Solid State Logic SSL 2 and SSL 2+

An integral and vital component of many studio and mobile recording setups – we wouldn’t like to wager how many sessions have been halted in their tracks by misplaced coffees and beers infiltrating these units. Cover offers peace of mind and protection against these little disasters. Custom

Decksaver Solid State Logic UC1

Custom moulded in the UK to fit the contours of the Solid State Logic UC1. Designed for the Digital DJ, super durable polycarbonate shell offers a high level of protection and slides straight into equipment bags, making it ideal for the travelling DJ. Shields faders and controls from dust, liquid

Decksaver Solid State Logic UF8

Custom moulded in the UK to fit the contours of the Solid State Logic UF8. Designed for the Digital DJ, super durable polycarbonate shell offers a high level of protection and slides straight into equipment bags, making it ideal for the travelling DJ. Shields faders and controls from dust, liquid

Decksaver SQUARP INSTRUMENTS HAPAX

Hapax boosts creativity as it can synchronize and sequence all of your synthesizers, DAWs and much more together, therefore, it is crucial you protect it!The Hapax utilizes a lot of touch-heavy pads, knobs and LCD screens, which are important to its use and operation. However, accidents can happen

Decksaver Zoom Podtrak P4

Have you ever considered how much you rely on your hardware? Units such as the Podtrak P4 sit at the very heart of your setup and without them, content cannot be captured. Dust, liquid and accidental impact have taken many a good hardware unit down over the years – this is where Decksaver steps

DJ Techtools Chroma Cover Midi Fighter Twister / Spectra / 3D / Classic

Protective dustcover lids for Midi Fighters. It was made to protect your expensive controllers from disaster both on-stage and in the home or studio. Think of the Chroma Cover as an investment in a protective shield that repels any liquid or impact issues and protects the perfection of your

Duratruss ASC AT-UJB1 Truss accessory

Original gigbag for Boxcorner model from the DT 34 series. Features two straps for easy transport. High quality zipers. Colour: Black. | Made in: China

Duratruss ASC AT-UJB2 Truss accessory

Original gigbag for two Boxcorner models from the DT 34 series. Features two straps for easy transport. High quality zipers. Colour: Black. | Made in: China

Duratruss DT 14-030 Rectangle truss

The DT14 system of DuraTruss is a decorative truss system. The DT14 is connected through a conical connection (spigot), trusspin and safetyclip. The DT14 is suitable for shops, displays or even at home as a decorative object. Through a boxcorner you realize 90° angles in all directions. There are

Duratruss DT 14-040 Rectangle truss

The DT14 system of DuraTruss is a decorative truss system. The DT14 is connected through a conical connection (spigot), trusspin and safetyclip. The DT14 is suitable for shops, displays or even at home as a decorative object. Through a boxcorner you realize 90° angles in all directions. There are

Duratruss DT 14-050 Rectangle truss

The DT14 system of DuraTruss is a decorative truss system. The DT14 is connected through a conical connection (spigot), trusspin and safetyclip. The DT14 is suitable for shops, displays or even at home as a decorative object. Through a boxcorner you realize 90° angles in all directions. There are

Duratruss DT 14 -Box Corner Rectangle truss

This Box Corner is the ideal connector for your DT 14 Truss system. The DT 14 Box Corner is perfect for making 90° angles in all directions. Standard included are 8 half conical connectors, 8 truss pins and 8 safety clips. Lenght: 100mm, Width: 100mm, Height: 100mm, Weight: 0,6kg. | Made in: China

Duratruss DT 22-050 Ladder truss

The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of 35mm aluminum tube with

Duratruss DT 22-BPM Truss base plate

DuraTruss DT 22-BPM - Base plate male. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four

Duratruss DT 22-C21H-L90 Ladder truss

2 way corner 90° horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are

Duratruss DT 22-C22H-L120 Ladder truss

2 way corner 120° horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are

Duratruss DT 22-C22V-L120 Ladder truss

2 way corner 120° vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are

Duratruss DT 22-C23H-L135 Ladder truss

2 way corner 135° horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are

Duratruss DT 22-C23V-L135 Ladder truss

2 way corner 135° vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are

Duratruss DT 22-C31H-LD Ladder truss

3 way corner 90° + down horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four

Duratruss DT 22-C31V-LD Ladder truss

3 way corner 90° + down vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes

Duratruss DT 22-C41H-X Ladder truss

4 way X-joint horizonatal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made

Duratruss DT 22-C41V-X Ladder truss

4 way X-joint vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of

Duratruss DT 22-C44H-LUD Ladder truss

4 way corner 90° + up + down, horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The

Duratruss DT 22-C44V-LUD Ladder truss

4 way corner 90° + up + down, vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four

Duratruss DT 22-T35H-T Ladder truss

3 way T-joint horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made

Duratruss DT 22-T36V-T Ladder truss

3 way T-joint horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made

Duratruss DT 22-T42H-TD Ladder truss

4 way T-joint + down horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes

Duratruss DT 22-T42V-TD Ladder truss

4 way T-joint + down vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are

Duratruss DT 22-WPM Truss base plate

Wall plate male. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of 35mm

Duratruss DT 23-050 Triangle truss

Straight construction with transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 220 x 194 mm. Weight: 1,4 kg. | Height (cm): 50.0 | Width

Duratruss DT 23/2-025 Triangle truss

Straight construction with transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. | Width (cm): 22.0 | Material: Aluminium | Made in: China | Weight: 1,1 kg | Package

Duratruss DT 23-BPM Truss base plate

Base plate male designed for stage construction. It is made of solid steel and includes half connectors. Dimensions: 240 x 212 x 5 mm. Weight: 1 kg. | Made in: China

Duratruss DT 23-C19-L45 Triangle truss

2-way construction with 45° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 1000 x 1000 x 194 mm. Weight: 3,2 kg. | Made in:

Duratruss DT 23-C21-L90 Triangle truss

2-way construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 194 mm. Weight: 2,1 kg. | Made in: China

Duratruss DT 23-C22-L120 Triangle truss

2-way construction with 120° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 194 mm. Weight: 2,2 kg. | Made in:

Duratruss DT 23-C23-L135 Triangle truss

2-way construction with 135° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 194 mm. Weight: 2,4 kg. | Made in:

Duratruss DT 23-C24-L90 Triangle truss

2-way apex out construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 220 mm. Weight: 2 kg. | Made

Duratruss DT 23-C24R-L90 Circle truss

2-way rounded corner with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 220 mm. Weight: 1,5 kg. | Made in:

Duratruss DT 23-C25-L90 Triangle truss

2-way apex in construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 220 mm. Weight: 2 kg. | Made in:

Duratruss DT 23-C25R-L90 Circle truss

2-way rounded corner with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 220 mm. Weight: 1,7 kg. | Made in:

Duratruss DT 23-C31-ULDR Triangle truss

3-way apex up right construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3

Duratruss DT 23-C32-ULDL Triangle truss

3-way apex up left construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3

Duratruss DT 23-C33-LD Triangle truss

3-way apex down right construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3,2

Duratruss DT 23-C34-LD Triangle truss

3-way apex down left construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3,2

Duratruss DT 23-C41 Triangle truss

4-way X-joint with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 194 mm. Weight: 2,7 kg. | Made in: China

Duratruss DT 23-C44-LUD Triangle truss

4 way corner + up + down right with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3 kg. | Made

Duratruss DT 23-C45-LUD Triangle truss

4 way corner + up + down left with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3 kg. | Made

Duratruss DT 23-C52-XU Triangle truss

5 way X-joint + up with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3,5 kg. | Made in: China

Duratruss DT 23 C61 Triangle truss

5 way T-joint + up + down with transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. | Made in: China

Duratruss DT 23-T35-VD Triangle truss

3-way T-joint apex down vertical construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm

Duratruss DT 23-T36H Triangle truss

3-way horizontal T-joint construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 194 mm. Weight: 2,4

Duratruss DT 23-T37V Triangle truss

3-way T-joint apex up vertical construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 220 mm

Duratruss DT 23-T42-DTD Triangle truss

4 way T-joint + down with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 550 mm. Weight: 3 kg. | Made in: China

Duratruss DT 23-T43-UTD Triangle truss

4-way T-joint + up unit for stage construction, with a 90° angle. It is made of steel, and can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3 kg. | Made in: China

Duratruss DT 23-T51-TUD Triangle truss

5 way T-joint + up + down with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 500 mm. Weight: 3,8 kg. | Made

Duratruss DT 23-WPM Truss base plate

Wall plate male designed for stage construction. It is made of solid steel and includes half connectors. Dimensions: 240 x 212 x 5 mm. Weight: 1 kg. | Made in: China

Duratruss DT 24-050 Rectangle truss

The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of 35mm aluminum tube with

Duratruss DT 24-BPM Truss base plate

Base plate male. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of 35mm

Duratruss DT 24-C21-L90 Rectangle truss

2 way corner 90°. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of 35mm

Duratruss DT 24-C21R-L90 Circle truss

The DT24 series is a 4-point-trussing-system with conical coupler (spigot), 2 way rounded corner 90°, trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made

Duratruss DT 24-C22-L120 Rectangle truss

2 way corner 120°. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of

Duratruss DT 24-C23-L135 Rectangle truss

2 way corner 135°. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of

Duratruss DT 24-C30-L90 Rectangle truss

3 way corner 90° + down. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made

Duratruss DT 24-C41 Rectangle truss

4 way X-joint 90°. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of

Duratruss DT 24-C51 Rectangle truss

5 way X-joint + down. The DT24 series is a 4-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are made of