Prices and availability may change several times a day. Check the current data directly in the e-shops. You can find all available colors and sizes directly in the e-shops.
Using the same low-noise power supply up-converter circuit as the Stampede OD SOV-2 overdrive pedal, the output of a single 9-volt battery is increased to a level that is capable of delivering sonic depth and a wide dynamic range that would be impossible with a standard 9-volt power supply. The result is hard-hitting distortion with a big low end that is similar to what you'd expect from a large amp stack driven hard. Gain and tone controls make it possible to dial in anything from a natural crunch to fuzzy, dirty distortion, providing a broad spectrum of tones that can add new dimensions to your music.TREBLE and BASS controls can be used to optimally match the pedal output to the amp being used for the most musical response. These controls, in combination with the GAIN control, give you an extraordinary range of sonic variation.In standard 'true bypass' circuits the instrument signal passes through two switch contacts when bypassed. The SOV-2 Single Contact True Bypass configuration ensures that the signal only passes through one switch contact when bypassed, for unmatched signal quality as well as reliability.Due to the adoption of the new double-contact grounding circuit (D.C.G. Circuit), by inserting a monaural plug into the output jack, the shield (sleeve) of the plug provides two points of contact to the pedal's ground circuit. By increasing the area of the point of contact, it becomes more difficult for a loose connection to occur, and provides the additional advantage of improved sound quality.In addition to indicating the pedal's on/off status, the SDT-2 LED provides effective visual battery power monitoring. When the battery voltage drops below 7 volts the LED will become dimmer and begin to go out. The effect will still operate at this voltage, but to ensure optimum performance the battery should be replaced as soon as possible. Power Supply: Adapter;Battery;9V Made in: Japan Controls: Gain;Bass;Output;Treble Type: Distortion Outputs: Jack 6,3 mm TS Number of Buttons: 1 Battery Type: 9V Package Contents: Manual Inputs: Jack 6,3 mm TS Battery Operation: Yes Colour: Yellow UK/EU Power supply included: No True Bypass: Yes USB: No
Color | Yellow |
Using the same low-noise power supply up-converter circuit as the Stampede OD SOV-2 overdrive pedal, the output of a single 9-volt battery is increased to a level that is capable of delivering sonic depth and a wide dynamic range that would be impossible with a standard 9-volt power supply. The
The Providence SOV-2 Stampede OD pedal is designed to deliver natural overdrive without obscuring the inherent characteristics and tone of the guitar being used. It features a special bipolar power supply that powers the internal circuitry with boosted voltage, providing a wider dynamic range than
The DT-C2 Dunlop Deluxe Headstock Tuner provides accurate chromatic tuning—all the way down to a low B—with an easy-to-read fourcolor display. The DT-C2 frequency is adjustable from 430–490Hz, and it features a silent metronome for visual cue practice, Mic and Clip modes for sound or
DuraTruss DT 22-BPM - Base plate male. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four
2 way corner 90° horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are
2 way corner 120° horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are
2 way corner 135° horizontal. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are
2 way corner 120° vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are
2 way corner 135° vertical. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling. The four tubes are
X-joint + up + down. 2 way rounded corner 90°. The DT22 series is a 2-point-trussing-system with conical coupler (spigot), trusspin and safety clip. The advantage of the quick connector system lies in the fact that it closes force-locking the belt tube and allows rapid assembly and dismantling
2 way corner 120°. The Duratruss DT31 is a 1-point trussing system, also referred as a ''pipe'', which is connected to a conical connector, bolt and split pin. The advantage of the quick connector system lies in the fact that it closes force-lockingly with the belt tube and allows rapid assembly
2 way corner 135°. The Duratruss DT31 is a 1-point trussing system, also referred as a ''pipe'', which is connected to a conical connector, bolt and split pin. The advantage of the quick connector system lies in the fact that it closes force-lockingly with the belt tube and allows rapid assembly
2 way corner 45°. The Duratruss DT31 is a 1-point trussing system, also referred as a ''pipe'', which is connected to a conical connector, bolt and split pin. The advantage of the quick connector system lies in the fact that it closes force-lockingly with the belt tube and allows rapid assembly
2 way corner 60°. The Duratruss DT31 is a 1-point trussing system, also referred as a ''pipe'', which is connected to a conical connector, bolt and split pin. The advantage of the quick connector system lies in the fact that it closes force-lockingly with the belt tube and allows rapid assembly
2 way corner 90°. The Duratruss DT31 is a 1-point trussing system, also referred as a ''pipe'', which is connected to a conical connector, bolt and split pin. The advantage of the quick connector system lies in the fact that it closes force-lockingly with the belt tube and allows rapid assembly
2 way corner 90° horizontal. The DT32 series is one of the most popular trussing systems duratruss has ever produced. The high load capacity combined with a very low weight are the features of this 29cm series with conical coupler. The advantage of the quick connector system lies in the fact that
2 way corner 120° horizontal. The DT32 series is one of the most popular trussing systems duratruss has ever produced. The high load capacity combined with a very low weight are the features of this 29cm series with conical coupler. The advantage of the quick connector system lies in the fact that
2 way corner 120° vertical. The DT32 series is one of the most popular trussing systems duratruss has ever produced. The high load capacity combined with a very low weight are the features of this 29cm series with conical coupler. The advantage of the quick connector system lies in the fact that
2 way corner 135° horizontal. The DT32 series is one of the most popular trussing systems duratruss has ever produced. The high load capacity combined with a very low weight are the features of this 29cm series with conical coupler. The advantage of the quick connector system lies in the fact that
2 way corner 135° vertical. The DT32 series is one of the most popular trussing systems duratruss has ever produced. The high load capacity combined with a very low weight are the features of this 29cm series with conical coupler. The advantage of the quick connector system lies in the fact that
2 way corner 90° vertical. The DT32 series is one of the most popular trussing systems duratruss has ever produced. The high load capacity combined with a very low weight are the features of this 29cm series with conical coupler. The advantage of the quick connector system lies in the fact that it
pitchbend (3 to +2 octaves), Momentary switch for hammeron and pulloff, mixable drysignal, drop tuning/capopitchable signal up to 7 semi tones or one octave up or down, 10 whammy effects, weight: 1,59kg, dimensions : 20,83cm X 19,63cm X 5,99cm, heavy metal chassis, poti for whammy/Hharmonizer
2-way apex in construction with 90° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 500 x 500 x 220 mm. Weight: 2 kg. | Made in:
2-way construction with 45° angle and transverse reinforcement, designed for stages. It is made of an alloy EN-AW 6060 T66, with tube diameter 35 mm x 2 mm and a cross brace diameter of 8 mm. It can be powdercoated in every RAL colour. Dimensions: 1000 x 1000 x 194 mm. Weight: 3,2 kg. | Made in: