Prices and availability may change several times a day. Check the current data directly in the e-shops. You can find all available colors and sizes directly in the e-shops.
25k Volume Pot, SOLDERLESS - Standard Strat™ sized volume replacement potentiometer. Package Quantity (pcs): 1 Made in: USA Variant: Short Shaft
Product EMG 25K Split Volume (Solderless) is assigned an EAN code 6543308007714.
Category | Fitness, Packaging |
EAN | 6543308007714 |
25k Volume Pot, SOLDERLESS - Standard Strat™ sized volume replacement potentiometer. | Package Quantity (pcs): 1 | Made in: USA | Variant: Short Shaft
25k Volume Pot, SOLDERLESS - Standard Strat™ sized volume replacement potentiometer. | Variant : Long Shaft | Made in : USA | Package Quantity (pcs) : 1
25k Volume Pot, SOLDERLESS - Standard Strat™ sized volume replacement potentiometer. | Package Quantity (pcs): 1 | Made in: USA
25k Tone Pot, SOLDERLESS - tone replacement potentiometer. | Package Quantity (pcs): 1 | Made in: USA | Variant: Short Shaft
25k Tone Pot, SOLDERLESS - tone replacement potentiometer. | Package Quantity (pcs) : 1 | Variant : Long Shaft | Made in : USA
25k Tone Pot, SOLDERLESS - tone replacement potentiometer. | Made in: USA | Package Quantity (pcs): 1
This solderless conversion kit is designed for 3 active EMG's with one dual mode pickup. This includes everything needed for installation of 2 EMG's and one TW/Dual Mode pickup in a 3 pickup configuration. The conversion kit includes a 5 Position Blade Switch, 1 standard volume, 1 Push Pull Pot
The EMG AB (Afterburner) is a boost you can use instead of your tone or volume knob (does not function as a tone or volume) and activate with variable gain push/pull pot. When the Push-Pull pot is in the “down” position there is no boost and the control has no effect. In the “up” position,
Dual 500K/250K split shaft potentiometer for control of volume and tone. Potentiometer is designed for Fender guitars and it will work with push-on style control knobs. The package also includes a mounting hardware. | | Made in: USA
The EMG B161(X4) 5-Position Switch Buss provides a convenient way to install EMG Pickups without soldering. The buss includes an input section for three pickups, a Supply buss for distributing 9V+ battery power to the pickups and accessories. A tone/effects send and return buss with bypass and an
Mono potentiometer with push / pull switch• one shaft• B500K (resistance 500 kOhm, (B) linear)• On / On DPDT• pre-equipped with PCB module MEC M 84002• suitable for use as a volume control for active sensors• solderless connector JST R5 2 mm• M10 x 0.75 mm threads• mounting diameter
The ABCX is an active EQ accessory that eliminates insertion loss and is designed to work with all EMG X series pickups that have an active tone pot. Insertion loss is a naturally occurring yet frustrating phenomenon that occurs most frequently with traditional balance pots, usually when it is in
The ABCX is an active EQ accessory that eliminates insertion loss and is designed to work with all EMG X series pickups that have an active tone pot. Insertion loss is a naturally occurring yet frustrating phenomenon that occurs most frequently with traditional balance pots, usually when it is in
For exceptional flexibility in tone at your fingertips, there is no better choice than the EXG Guitar Expander. The frequency response of the EXG is similar to a typical guitar amp equalization. The lows and highs are boosted while the midrange is dipped out as you turn the knob up. The result is a
The SPC or 'Strat Presence Control' is often called the fat control. The original intent of the SPC was to allow guitar players to boost the midrange of their single coil pickup to give it a sound similar to a humbucker. This is accomplished by boosting the gain in a broad mid-band fashion and
The PA2 is a boost preamp you can mount to your guitar and turn on/off via minitoggle switch. It's the perfect solution if you want to increase your instrument's overall volume for solos or push an amp on the edge of breakup into overdrive. It has an internal trim pot so you can preset the amount
The Area Strat Replacement Pickguard features solderless connectors for easy installation in any guitar with a standard 11-hole pickguard. The pickup configuration for the Area Pickguard is an Area 58 neck / Area 67 middle / Area 61 bridge combination for great vintage sounds with no hum. The Area
Linear potentiometer 1 Meg and 3/8''potentiometer shaft. Split shaft design. Works with push-on style knobs (no set screw). Mounting hardware not included. Used as a master volume control on the American Vintage '62 Jazz master (US) and Classic Player Series (Mexico) models manufactured from
250K push-pull split-shaft potentiometer lets you add a coil tap or phase switch to your guitar without drilling extra holes. Mounting hardware included. | Made in: South Korea
Set of three plastic push-on control knobs designed to fit 1/4' split-shaft potentiometers on nearly all U.S.- and Mexico-made Stratocaster models manufactured from 1954-present. | Original Colour by Producer: Black | Made in: USA
Featherlight, loose-fitting and ventilated black shorts with integrated brief for exceptional freedom of movement when running. | The Racing Split Short was designed to perfectly complement the Racing shirt for weightless running in hot or humid conditions. A thin, membrane material guarantees
Featherlight, loose-fitting and ventilated black shorts with integrated brief for exceptional freedom of movement when running. | The Racing Split Short was designed to perfectly complement the Racing shirt for weightless running in hot or humid conditions. A thin, membrane material guarantees
Featherlight, loose-fitting and ventilated black shorts with integrated brief for exceptional freedom of movement when running. | The Racing Split Short was designed to perfectly complement the Racing shirt for weightless running in hot or humid conditions. A thin, membrane material guarantees
Featherlight, loose-fitting and ventilated black shorts with integrated brief for exceptional freedom of movement when running. | The Racing Split Short was designed to perfectly complement the Racing shirt for weightless running in hot or humid conditions. A thin, membrane material guarantees